Note: The answer is for reference only, you need to understand all question.

QUESTION 1
Refer to the exhibit.




The customer has an MPLS Layer 3 VPN service CE-A is not able to ping the CE-B loopback address 10.60.6.6 CE-A is able to ping the CE-B network interface address 172.16.60.66. What must be added to the configuration to allow the loopback ping to work?

A.
The PE-B configuration needs a neighbor 10.60.6.6 command added

B.
The PE-B configuration needs interface loopback0 added under vrf red area 0

C.
The CE-B configuration needs to static route added for the PE-B connected interface

D.
The CE-B configuration needs network 10.60.6.6 under router ospf 1



Answer: D


QUESTION 2
Refer to the exhibit.




What type of MPLS LAYER 3 VPN configurations is represented?

A.
Simple two-VPN scenario

B.
Overlapping VPNs

C.
Central services VPNs

D.
Extranet VPNs



Answer: C


QUESTION 3
In a service provider layer 3 MPLS VPN implementations, what is the minimum number of routing on the PE routers?

A.
Three

B.
Four

C.
Five

D.
Six



Answer: A


QUESTION 4
Refer to the exhibit.




The commands on the figure were executed from a cisco ASR 9000 series router. The remote end of ping is cisco XR 12000 series router. Which statement is true?

A.
The XR 12000 has an access list that blacks the MPLS pseudowire ping

B.
The interface connected to the XR 12000 is not running LDP

C.
These results will occur during convergence when MPLS LDP sync is enabled

D.
The MPLS pseudowire ping was not sent



Answer: D


QUESTION 5
Refer to the exhibit.




The output from the debug command is from the Cisco XR12000 series Router, which statement is true?

A.
The output is the result of single iteration of mpls ping executed on the cisco ASR 9000 Series Router'

B.
The output is the result of single iteration of mpls ping executed on the cisco ASR 9000 series Router

C.
The packets did not reach its destination because the control word was not found

D.
The output is the result of single iteration of mpls ping executed on the cisco CRS-1 carrier routing system.



Answer: C


QUESTION 6
Refer to the exhibit.




The commands were exceeded on the cisco XR 12000 PE. Which statement is true?

A.
The outer label for prefix 10.22.22.22 is 143989.

B.
The outer label for prefix 10.22.22.22 is 16000.

C.
The outer label for prefix 10.22.22.22 is implNull.

D.
Prefix 10.22.22.22 has no outer label.



Answer: A


QUESTION 7
You have configured a MPLS-TE tunnel with a predefined explicit path as primary and dynamic path as the backup. The tunnel was designed to carry customer traffic from site A to site B. although the MPLS-TE tunnel is set up. It is not carrying the traffic. Traffic has to go to net work 171.68.0.0/16 connected to site B. Which three show commands would you use to identify and resolve the issue?

A.
Show mpls traffic-eng-link-management bandwidth to check the bandwidth is available.

B.
Shoe ip cef network-number to check if tabs are imposed

C.
Show mpls traffic-eng topology ipg-id ospf network number brief to check routing issue

D.
Show mpls traffic-eng autoroute to check auto routing is enabled

E.
Show mpls forwarding-table LABEL-number details to outgoing tags

F.
Show ip cef tunnel 1 to check traffic is passing through the tunnel



Answer: DE


QUESTION 8
Refer to the exhibit.




Is nonstop forwarding enabled or disabled, and which part of show command can be used to determine this?

A.
Enabled, graceful-restart

B.
Enabled, session protection

C.
Disabled, graceful-restart

D.
Disabled, session protection



Answer: A


QUESTION 9
Refer to the exhibit.




What two problems are associated with this show MPLS forwarding command output; given that this command only shows forwarding information for CEs faces interfaces and associated statistics? (Choose two)

A.
Lin 1 and 3 indicate the problem

B.
Lin 2 and 4 indicate the problem

C.
LDP is not active on AT 12/3.1283 and se 9/0/7.0 that is why packets are sent as IP packets and no MPLS packets

D.
There is a possible routing loop which makes pe-1 a transit router for the VRFs which are
assigned to Gi 14/.1271 and AT 12/3.1132

E.
There is label corruption for VRFs where Gi 14/1.1271 and AT 12/3.1132 belong to, the value of a locally assigned label cannot be more than the value of outgoing label



Answer: BE


QUESTION 10
You have been assigned the task of collecting the relevant information for trouble shooting a Layer 3 MPLS VPN routing issue across two (same VPN) for a customer. After initial diagnostics you have ruled out any connectivity issues and any hardware or software bugs. Which four steps should you use to collect information for troubleshooting the VPN routing issue? (Choose four)

A.
Redistribution of routes into MP-BGP

B.
Route fillers that might prevent routes from propagating

C.
Interface state between PE and CE devices

D.
VRF route target import and export details

E.
MPLS forwarding state between PE and core routers

F.
VRF route limit on the PE devices

G.
Interface error counters on the customer-facing PE interface



Answer: ABDE


QUESTION 11
Which three MPLS services require MPLS layer 2 VPNs? (Choose three)

A.
Any-to-any interworking

B.
Central services VPN

C.
VPLS

D.
VPWS



Answer: ACD


QUESTION 12
A service provider is running OSPF and has turned the network for fast convergence. The service provider has determined that its routers should also be configured for LDP synchronization. If the service provider follows ITIL-based practices, how should this change be treated?

A.
As a standard change

B.
As a minor change

C.
As a major change

D.
As an emergency change



Answer: D


QUESTION 13
What are three basic functional requirements when configuring MPLS layer 2 VPLS? (Choose three)

A.
A CE to PE routing protocol must be used to exchange routing prefixes


B.
A full mesh of pseudowire (emulated VC) connections must be used between PE routers

C.
Each PE must have a VFI configured

D.
LDP protocol must be running

E.
Auto discovery is needed to identify endpoints outside of the VPLS domain.



Answer: BCD


QUESTION 14
Refer to the exhibit.




Which statement about the two show command is true>

A.
The CE-PE routing protocol between the PE and customer_1 CE router is BGP

B.
The PE router ha learned four prefixes over the multiprotocol BGP session

C.
192.168.1.33 is CE router and 150.1.11.17 is the PE router

D.
The PE router is supporting more than one MPLS layer 3 VPN customers



Answer: B


QUESTION 15
What are four essential parts of the MP-BGP VPNv4 update? (Choose four)

A.
LDP label

B.
VPN label

C.
IPv4 prefix with route descriptor

D.
LSP identifier

E.
BGP next-hop address

F.
Route targets (extended communities)



Answer: BCEF


QUESTION 16
What function does MP-BGP provides that is required for MPLS layer 3 VPM services?

A.
MP-BGP modifies or swaps the LDP label to indicate the next-hop router in MPLS cloud

B.
MP-BGP provides the penultimate hop popping function

C.
MP-BGP performs the standard MPLS LDP functions in layer 3 environment

D.
MP-BGP advertises the VPN label and identifies the correct egress PE interface



Answer: D


QUESTION 17
Refer to the exhibit.




A layer 3 VPN is configured between PE1 and PE2. CE1 is connected to PE1. CE2 is connected to PE2. CE1 and CE2 are in VRF red. From which router does the prefix 10.170.170.0/24 originates?

A.
CE1

B.
PE1

C.
PE2

D.
CE2



Answer: A


QUESTION 18
What two mechanisms are used to improve both MPLS network performance and availability? (Choose two)

A.
LDP and BGP synchronization

B.
Stateful switchover with fast Reroute

C.
Stateful switchover

D.
BGP timer tuning

E.
Stateful switchover with NSR



Answer: AB


QUESTION 19
A cisco 7600 series Router is experiencing high CPU utilization and poor forwarding performance. Investigation reveals that packet forwarding has been punted to the RP. What are two possible causes of this behavior? (Choose two)

A.
The routing table is too large

B.
Liberal retention mode has been disabled

C.
An insufficient number of flow masks are configured

D.
A large number of access list entries are configured

E.
IGP timers need to be returned to improve routing convergence



Answer: BD


QUESTION 20
Layer 3 VPN is the primary service running on your network. You have POP locations and recently you have seen memory and CPU utilization go above 90% in two out put of four PE devices in one POP location. You have maximum-route-limit configured for each VPN. What additional parameter should be monitored proactively to address these issues?

A.
Number of prefixes per VRF route in the router

B.
Number of VRFs configured on each Router

C.
Number of route targets for each VRF

D.
LDP neighbor statistics for any flaps

E.
Packets in and out for each VRF



Answer: D


QUESTION 21
Which MPLS layer 2 VPN services strip 802 .1q tags before encapsulating the frame? (Choose two)

A.
Ethernet over MPLS port mode

B.
Ethernet over MPLS VLAN mode

C.
MPLS Bridging

D.
MPLS VPLS



Answer: BD


QUESTION 22
Refer to the exhibit.




Which two statements are true? (Choose two)

A.
150.1.12.16 is directly connected subnet

B.
The router is advertising label 20 destinations 192.168.1.33.

C.
The upstream P router is perform PHP for destinations on 192.168.1.48

D.
The forward data to device on the network 150.1.12.32 the router will remove label 22 and impose label 23



Answer: BC


QUESTION 23
Refer to the exhibit.




The command was executed on cisco XR12000 series router. The router is directly connected to a remote PE, which has router ID of 192.168.253.3. A single CE is connected to the remote PE. Based on the command output, which label location mode is remote PE running?

A.
Per-prefix

B.
Per-ce

C.
Per-vrf

D.
Per-pe



Answer: C


QUESTION 24
Refer to the exhibit.




The command on the diagram was executed from a cisco ASR 9000 router. Which statement is true?

A.
192.168.253.1 is router ID of the ASR9000

B.
The ASR 9000 will use label 16004 to reach 192.168.253.1

C.
The ASR 9000 will perform penultimate hop popping on packets destined to 192.168.253.1

D.
The ASR 9000 advertises a label of IMP-NULL to its peers for 192.168.253.1 reachability



Answer: C


QUESTION 25
You have implemented IMPLS-TE on the core and enabled Fast Reroute. BFD is configured on the core facing links. Every thing was working normally until last month when you added video service on the network. Because of business requirements, video packets are treated as high priority and 70% of bandwidth is allocated for the low latency queue. Recently you noticed BFD session losses and MPLS-TE tunnel flaps on the network. Which parameter should you have mentioned proactively to avoid this issue?

A.
BFD session timers and hello message

B.
MPLS-TE tunnel bandwidth and utilization

C.
QoS drops each class of service on core-facing links

D.
CPU utilization on the PE routers

E.
Latency and jitter between PE routers



Answer: A


QUESTION 26
Which decode corresponds correctly to this MPLS header. 0x00 0x04 0xAB 0xFE?

A.
Label: 0004, Exp AB. S:1.TTL:7E

B.
Label: 0004A. TTL:BF.Exp:8. S:0

C.
Label: 0004A. Exp:8.S:0

D.
Label: 0004. TTL:AB.Exp:7E.S:1



Answer: B


QUESTION 27
What four layer 2 MPLS VPN parameters are collected from a customer service record database to trouble a VPN connectivity issue? (Choose four)

A.
Attachment circuit information

B.
UNI interface encapsulation

C.
Hop-by-hop LDP information

D.
Virtual circuit ID information

E.
Unique service identifier

F.
PE loopback information

G.
Layer 2 MPLS VPN service type



Answer: ABDG


QUESTION 28
DRAG DROP
Drag the attributes on the left to the appropriate categories on the right. Note that not all slots may be uses.




Answer:




QUESTION 29
The SP NOC has determined that a significant number of broadcast packets are being received from customer A. which could be a DoS attack. Customer A is using MPLS layer VPLS services the exercise broadcast traffic is causing degrading performance and over utilizing the access links. Which of the cisco IOS XR MPLS layer 2 configuration parameters can be used to mitigate the problem?

A.
The storm control parameter under the 12vpn bridge group

B.
The storm control parameter under the 12vpn xconnect group

C.
The limit-broadcast parameter under the 12vpn bridge group

D.
The storm control parameter under the 12vpn xconnect



Answer: A


QUESTION 30
A customer has stated that they can not access network 10.450.16.0/24 from one of there sites (Site c). The customer has a layer 3 MPLS VPN between three sites (site A, site B, site C) connected in full mesh topology. They do not have any issues with accessing after network addresses located in site A and site B. Assuring the PE devices are running Cisco IOS, what are the two troubleshooting commands you should execute on the PE router connected to site C

A.
Show ip vrf VRFNAME detail to check the route targets

B.
Show ip vrf VRFNAME detail to check the vrf routes

C.
Show mpls 12transport binding to check local and remote labels

D.
Show MPLS interfaces INTERFACENAME detail to check MTU size

E.
Show ip bgp vpnv4 vrf VRFNAME to check advertised VPNv4 prefixes



Answer: ACE


QUESTION 31
Refer to the exhibit.




The command was executed on a cisco XR12000 series router. Which statement about the tunnel displayed is true?

A.
The command was executed on the head end of the tunnel

B.
A label of 16003 will be used to reach the next hop for the tunnel

C.
10.200.200.0 is the IP address of remote interface of the next downstream hop for the tunnel.

D.
The command was executed on the tail end of the tunnel



Answer: D


QUESTION 32
Refer to the exhibit.




The commands were executing from VKG-3, which is the cisco ASR 9000 Series router. Which statement is true?

A.
Layer 2 reachability can be achieved between 7200a and 7200b with the current configuration on VKG-3

B.
Layer 2 reachability between 7200a and 7200b will fail because of VLAN mismatch configured on VKG-3

C.
Layer 2 reachability between 7200a and 7200b will fail because VKG-3 needs "rewrite egress tag push 1 symmetric " configured under both interfaces

D.
Layer 2 reachability between 7200a and 7200b will fail because the MTU needs to be increased 1504 to include for the VLAN header file



Answer: A


QUESTION 33
What are three characteristics that define MP-BGP performance? (Choose three)

A.
Convergence upon failure and recovery

B.
Time to establish a tunnel

C.
Import and export of VPNv4 routes

D.
Time to complete a SPF calculation

E.
Route table scanning for changes

F.
Time to synchronize with LDP



Answer: CE


QUESTION 34
Refer to the exhibit.




Which statement best describes the Cisco IOS XR VRF protection that is configured?

A.
The maximum number of configured VPNs is limited to 1000 with an active limit of 75

B.
The number of prefixes for VPNs number 1000 is limited to 75

C.
The number of VRF table entries is limited to 1000, and a syslog message will be sent at 75%

D.
The maximum number of pseudowire VCs is limited to 1000 and a syslog message will be sent at 75%



Answer: C


QUESTION 35
Refer to the exhibit.




The show interface statistic was taken five minutes after the interface counter was cleared.
What problem is indicated in the exhibit?

A.
The hardware forwarding capacity of the router has been exceeded

B.
The IGP and LDP of router need to be synchronized

C.
The RP has just failed over from the primary to standby

D.
The IGP timers of the router need to be turned



Answer: A


QUESTION 36
DRAG DROP
Refer to Exhibit. MPLS-TE is configured in the core and BFD is used for faster link failure detection. Currently the MPLS-TE tunnels are flapping. Identify the Symptom of the flapping, the root cause of the issue, and the resolution. Click and drag the elements on the left to the correct identifier on the right. It is possible that you will not use all the elements.




Answer:




QUESTION 37
Refer to the exhibit.




What could cause the pseudowire for bridge group GROUP5 to be down?

A.
An interface along the LSP is not running LDP

B.
The PW type needs to be changed to be VLAN mode

C.
The MTU needs to be increased by four to include the VLAN header

D.
The local and remote labels do not match



Answer: D


QUESTION 38
Which two statements describe when deployment of IP SLA could be regarded as standard or minor change as defined by ITIL? (Choose two)

A.
A low-frequency probe is being placed on one router for limited time.

B.
A high-frequency probe is being placed on one router for limited time.

C.
A low-frequency probe is being deployed to a few routers for a limited time.

D.
A low-frequency probe is being deployed to a few routers permanently

E.
A low-frequency probe is being deployed across the network for limited time

F.
A low-frequency probe is being deployed across the network permanently



Answer: AC


QUESTION 39
Refer to the exhibit.




Some of your customers are reporting poor network performance when they use FTP to transfer large data files across your MPLS VPN core. Recently, some backbone links in your MPLS VPN core have been upgraded from POS OC-48 to the new 10 Gigabit Ethernet. You have collected the output of the traceroute mpls ipv4 command with the remote PE as Destination. All devices are running cisco IOS. What must be fixed in network to resolve the issue?

A.
MPLS should be enabled on router ID 103.103.103.2.

B.
MTU on 78.78.78.2 has to be reduced to 4072.

C.
Exp is set to 0, which causes FTP traffic to be dropped.

D.
MTU on 110.110.110.1 should be changed to 4072.



Answer: A


QUESTION 40
You have designed and implemented MPLS-TE for fast router in your network core. Your network core consists of Cisco CRS-1 carrier routing System devices interconnected using XDM and Sonet Transport. You are using OSPF as the IGP, and MP-BGP is running on the PE devices to support Layer 3 VPN services. You are offering voice service over VPN circuits. So you want a link convergence of no greater than 100ms. Which option should you use for faster link failure detection and to improve the performance of your network?

A.
Use OSPF fast hello packets with dead-interval and hello multiplier

B.
Reduce MP-BGP hello timers between the neighbors

C.
Configure MPLS-TE tunnels with the dynamic backup option

D.
Configure MPLS-TE tunnels to autoroute announce

E.
Configure BFD on the core links with the appropriate BFD multiplier.



Answer: E


QUESTION 41
Which two IP SLA probe types can be used to monitor MPLS and VPNS for SLA compliance? (Choose two)

A.
UDP echo

B.
UDP echo ping

C.
MPLS LSP ping

D.
UDP delay

E.
VRF

F.
HTTP



Answer: CE


QUESTION 42
Refer to the exhibit.




Given the partial configuration, which statement is true?

A.
The 209.165.200.230 router is a P router

B.
The 209.165.200.230 router is a CE router

C.
The 209.165.200.230 router is a PE router

D.
The 209.165.200.230 router is a customer oriented behind the CE router



Answer: C


QUESTION 43
What happens to a captured ingress MPLS packet that has the header 0x00 0x00 0x7B 0x01?

A.
The packet will be dropped because it uses an incorrect label

B.
The packet will be dropped because it reached its TTL limit

C.
The packet will be dropped because its EXP value is corrupted

D.
The packet will be MPLS switched because nothing is wrong with it



Answer: B


QUESTION 44
DRAG DROP
Drag the list of commands on the left to the proper command categories on the right.




Answer:




QUESTION 45
Which four tasks are used to configure MPLS? (Choose four)

A.
Create a VRF instance for the VPN

B.
Assign customer interfaces (access links ) to a VPN

C.
Enable the VFI and MPLS encapsulation

D.
Configure the TE tunnel per PE interface

E.
Configure the IP address on the VRF interface or subinterface

F.
Configure the CE to PE customer routing



Answer: ABCE


QUESTION 46
Which three layer 2 products are supported on the attachment circuit by Cisco IOS Layer 2 VPNs? (Choose three)

A.
EtherChannel

B.
Token Ring

C.
HDLC

D.
Multilink PPP'

E.
Frame Relay

F.
AAL5



Answer: CDE


QUESTION 47
Customer A is experiencing intermittent network performance problems. The SP NOC has determined that the "MPLS blackhole" is occurring during network convergence events. The suspected cause of the PLS VPN traffic is that the customer's IGP (OSPF) is converging than the LDP. What MPLS feature can be configured to eliminate the problem?

A.
Decrease the OSPF convergence timing (throttle timer)

B.
MPLS VRF protection feature

C.
MPLS fast reroute feature

D.
MPLS LDP Sync feature in OSPF

E.
Use Cisco MPLS Auto bandwidth Allocator



Answer: D


QUESTION 48
Refer to the exhibit.




A service provider sees the following output indicating some problems. What are two possible causes? (Choose two)

A.
The router has not been configured with SSO

B.
The router has been inappropriately dimensioned policy feature card

C.
The IGP timers of the router have been overturned

D.
The router has not been configured with MPLS TE automatic tunnels and fast Reroute

E.
The router has too many entries on its routing table



Answer: BE


QUESTION 49
When MPLS VPN services are implemented, which CE-PE routing method does not require the use of the redistribute command to advertise customer routes between sites?

A.
Static routing

B.
RIP

C.
EIGRP

D.
OSPF

E.
BGP



Answer: E


QUESTION 50
You have configured a layer 2 VPN circuit between two routers, PE1 and PE4. For some reason the VC circuit Is not coming up. You checked the status and VC was downed at both sides. After careful verification you have ruled out any layer 2 VPN control plane configuration issues. Assuring that PE devices are running cisco IOS, what two additional troubleshooting steps should help identifying the problem? (Choose two)

A.
Show mpls forwarding-table for local circuit mismatch

B.
Show mpls 12transport hw-capability to check hardware capability

C.
Show mpls 12transport binding to check for MTU

D.
Show MPL12transport binding to check VC labels



Answer: D


QUESTION 51
What does this Cease Notification Syslog message indicate? May 19.12.43.45 CET: % BGP-3-NOTIFICATION: received from neighbor 10.1.2.3 6/1 (cease) 0 bytes.

A.
The port is shut down

B.
The connection was rejected

C.
BGP became disabled

D.
The maximum number of prefixes was reached



Answer: B


QUESTION 52
You want to collect net flow-related information from your core links. You also want label switch traffic to be included in the information collected by NetFlow. You have MPLS, MPLS VPN, and protected TE tunnel in your core. How many labels should NetFlow analyze to collect information for all types of MPLS applications used in your core network?

A.
Two labels

B.
Three labels

C.
four labels

D.
five labels



Answer: B


QUESTION 53
When MPLS layer 3 VPN services are implemented, what is the function of the VRF table?

A.
The VRF table determines the pseudowire virtual circuits used to for forward labeled packets

B.
Multiple VRF instances are used to isolate potently overlapping routing and forwarding information for VPNs.

C.
VRF tables are used to translate IP routing prefixes

D.
OSPF and IS-IS routing prefixes are MAPPED to there corresponding MPLS labeled prefixes in the VRF table. The prefixes are used by the PE to map forwarded packets between MPLS and NON-MPLS circuits



Answer: B


QUESTION 54
Which cisco IOS command should be used to verify that frames are being forwarded on a VC by an egress PE?

A.
Show MPLS forwarding tables

B.
Show MPLS interface forwarding

C.
Show 12 VPN counters forwarding session

D.
Show 12 VPN counters forwarding statistics



Answer: A


QUESTION 55
Your company has decided to deploy a MPLS network with VPNs. The customer that will be using the network is demanding service level agreements with your company. How can you monitor the SLAs for violations?

A.
RMON

B.
Event management system

C.
Asset management system

D.
CNR

E.
IP SLA



Answer: E


QUESTION 56
Which command should be used to verify that IS-IS has been properly configured to support MPLS TE?

A.
Show mpls isis traffic-eng advertisements

B.
Show isis mpls traffic-eng adjacency-log

C.
Show isis mpls traffic-eng advertisements

D.
Show isis mpls traffic-eng tunnel

E.
Show mpls isis traffic-eng adjacency-log



Answer: C


QUESTION 57
Which statement about LSP ping is true?

A.
LSP ping access ICMP packets

B.
A successful LSP ping ensures that the echo-reply are labled

C.
If an IP ping exceeds, than an LSP ping succeed if MPLS is enabled along the path

D.
A successful LSP ping validates reachability to the destination along the MPLS data plane



Answer: D


QUESTION 58
What does the auto tunnel template interface configure?

A.
MPLS TE tunnel mesh groups

B.
Virtual private LAN services

C.
MPLS VPN VRF instances

D.
MP-BGP peering

E.
LDP tunnels

F.
MPLS TE tunnel dynamic route



Answer: A


QUESTION 59
You have been asked to compare parameters of layer 2 MPLS vpn services at two remote ends using the show mpls 12 binding command What three items of relevant information should you use to ensure that layer two VPN parameters are configured correctly? (Choose three)

A.
Local and remote labels

B.
Encapsulation

C.
VC type

D.
VCCV

E.
VC ID

F.
MTU



Answer: ACD


QUESTION 60
Refer to the exhibit.




While configuring the customer access link is cisco IOS XR software. What must be done when assigning an interface to the VRF?

A.
Configure the neighbor LDP before accessing the interface to the VRF

B.
Configure the IP address to the interface before assigning the interface to the VRF

C.
Remove the customer access link before assigning the interface to the VRF

D.
Remove any address configuring before assigning the interface to the VRF



Answer: D


QUESTION 61
Refer to the exhibit.




With this template configured and applied to cisco XR 12000series Router, could a CPE device use the traceroute command to reveal the core network?

A.
Yes, traceroute is not disabled.

B.
Yes, discovery targeted-hello accept allows it

C.
No it is disabled with mpls ip-ttl-propagate disable

D.
No, session protection stops traceroute

E.
Only if traceroute mpls was used

F.
Only if traceroute 6 was used



Answer: C


QUESTION 62
What function does the penultimate LSR perform to help optimize MPLS?

A.
Pops the label before packet reaches the PE router

B.
Restore the original ingress settings to the EXP field

C.
Ensure that the LSP is Taking the shortest path

D.
Verifies that there are no loops in the path



Answer: A


QUESTION 63
Refer to the exhibit.




The partial show run command out put is from PE router that provides MPLS VPN services to customer_1. What is the routing protocol and AS number used between the PE router and customer_1 CE router?

A.
BGP AS 65001

B.
Multiprotocol BGP

C.
EIGRP AS 10

D.
EIGRP AS 20



Answer: C


QUESTION 64
Refer to the exhibit.




You are troubleshooting a connectivity problem between the CE routers in your network running IS-IS. You login to one of the routers and execute a show log. What is the problem associated with these message?

A.
Protocol mismatch

B.
Mismatch area ID

C.
Mismatch MTU size

D.
Mismatch of features

E.
Wrong ip address applied



Answer: D


QUESTION 65
What minimum commands are necessary to initiate MPLS on a cisco IOS router?

A.
In global configuration mode, execute the mpls ip command

B.
In global configuration mode, execute the mpls ip command on every participating interface.

C.
In global configuration mode, execute the mpls ip command. Interface configuration mode executes the mpls ip command on every participating interface.

D.
In global configuration mode, execute the mpls ip command in Mpls configuration mode specifies each participating interface using the interface interface command.



Answer: B


QUESTION 66
Refer to the exhibit.




The commands were exceeded on the cisco XR 12000 PE. Which statement is true?

A.
The outer label for prefix 10.22.22.22 is 143989.

B.
The outer label for prefix 10.22.22.22 is 16000.

C.
The outer label for prefix 10.22.22.22 is implNull.

D.
Prefix 10.22.22.22 has no outer label.



Answer: A


QUESTION 67
DRAG DROP
Refer to Exhibit. MPLS-TE is configured in the core and BFD is used for faster link failure detection. Currently the MPLS-TE tunnels are flapping. Identify the Symptom of the flapping, the root cause of the issue, and the resolution. Click and drag the elements on the left to the correct identifier on the right. It is possible that you will not use all the elements.




Answer:




QUESTION 68
Refer to the exhibit.




Is nonstop forwarding enabled or disabled, and which part of show command can be used to determine this?

A.
Enabled, graceful-restart

B.
Enabled, session protection

C.
Disabled, graceful-restart

D.
Disabled, session protection



Answer: A


QUESTION 69
What are three basic functional requirements when configuring MPLS layer 2 VPLS? (Choose three)

A.
A CE to PE routing protocol must be used to exchange routing prefixes

B.
A full mesh of pseudowire (emulated VC) connections must be used between PE routers

C.
Each PE must have a VFI configured

D.
LDP protocol must be running

E.
Auto discovery is needed to identify endpoints outside of the VPLS domain.



Answer: BCD


QUESTION 70
A cisco 7600 series Router is experiencing high CPU utilization and poor forwarding performance. Investigation reveals that packet forwarding has been punted to the RP. What are two possible causes of this behavior? (Choose two)

A.
The routing table is too large

B.
Liberal retention mode has been disabled

C.
An insufficient number of flow masks are configured

D.
A large number of access list entries are configured

E.
IGP timers need to be returned to improve routing convergence



Answer: BD


QUESTION 71
DRAG DROP
Refer to Exhibit. MPLS-TE is configured in the core and BFD is used for faster link failure detection. Currently the MPLS-TE tunnels are flapping. Identify the Symptom of the flapping, the root cause of the issue, and the resolution. Click and drag the elements on the left to the correct identifier on the right. It is possible that you will not use all the elements.




Answer:




QUESTION 72
You have designed and implemented MPLS-TE for fast router in your network core. Your network core consists of Cisco CRS-1 carrier routing System devices interconnected using XDM and Sonet Transport. You are using OSPF as the IGP, and MP-BGP is running on the PE devices to support Layer 3 VPN services. You are offering voice service over VPN circuits. So you want a link convergence of no greater than 100ms. Which option should you use for faster link failure detection and to improve the performance of your network?

A.
Use OSPF fast hello packets with dead-interval and hello multiplier

B.
Reduce MP-BGP hello timers between the neighbors

C.
Configure MPLS-TE tunnels with the dynamic backup option

D.
Configure MPLS-TE tunnels to autoroute announce

E.
Configure BFD on the core links with the appropriate BFD multiplier.



Answer: E


QUESTION 73
What does this Cease Notification Syslog message indicate? May 19.12.43.45 CET: % BGP-3-NOTIFICATION: received from neighbor 10.1.2.3 6/1 (cease) 0 bytes.

A.
The port is shut down

B.
The connection was rejected

C.
BGP became disabled

D.
The maximum number of prefixes was reached



Answer: B


QUESTION 74
Which command should be used to verify that IS-IS has been properly configured to support MPLS TE?

A.
Show mpls isis traffic-eng advertisements

B.
Show isis mpls traffic-eng adjacency-log

C.
Show isis mpls traffic-eng advertisements

D.
Show isis mpls traffic-eng tunnel

E.
Show mpls isis traffic-eng adjacency-log



Answer: C


QUESTION 75
Refer to the exhibit.




With this template configured and applied to cisco XR 12000series Router, could a CPE device use the traceroute command to reveal the core network?

A.
Yes, traceroute is not disabled.

B.
Yes, discovery targeted-hello accept allows it

C.
No it is disabled with mpls ip-ttl-propagate disable

D.
No, session protection stops traceroute

E.
Only if traceroute mpls was used

F.
Only if traceroute 6 was used



Answer: C