Note: The answer is for reference only, you need to understand all question.
QUESTION 1
As a network engineer at Cisco.com, you are responsible for Cisco network. Which will be necessarily taken into consideration when implementing Syslogging in your network?
A.Log all messages to the system buffer so that they can be displayed when accessing the router. B.Use SSH to access your Syslog information. C.Enable the highest level of Syslogging available to ensure you log all possible event messages. D.Syncronize clocks on the network with a protocol such as Network Time Protocol.
Answer: D


QUESTION 2
Which classes does the U.S. government place classified data into? (Choose three.)
A. SBU
B. Confidential
C. Secret
D. Top-secret
Answer: BCD


QUESTION 3
You are a network technician at Cisco.com. Which description is correct when you have generated RSA keys on your Cisco router to prepare for secure device management?
A.All vty ports are automatically enabled for SSH to provide secure management. B.The SSH protocol is automatically enabled. C.You must then zeroize the keys to reset secure shell before configuring other parameters. D.You must then specify the general-purpose key size used for authentication with the crypto key generate rsa
general-keys modulus command.
Answer: B
QUESTION 4
Which method is of gaining access to a system that bypasses normal security measures?

A. Creating a back door
B. Starting a Smurf attack
C. Conducting social engineering
D. Launching a DoS attack
Answer: A


QUESTION 5
As a candidate for CCNA examination, when you are familiar with the basic commands, if you input the command "enable secret level 5 password" in the global mode , what does it indicate?
A. Set the enable secret command to privilege level 5.
B. The enable secret password is hashed using SHA.
C. The enable secret password is hashed using MD5.
D. The enable secret password is encrypted using Cisco proprietary level 5 encryption.
E. The enable secret password is for accessing exec privilege level 5.
Answer: E


QUESTION 6
Which statement is true about a Smurf attack?
A.It sends ping requests to a subnet, requesting that devices on that subnet send ping replies to a target system.
B.It intercepts the third step in a TCP three-way handshake to hijack a session.
C.It uses Trojan horse applications to create a distributed collection of "zombie" computers, which can be used to launch a coordinated DDoS attack.
D.It sends ping requests in segments of an invalid size.
Answer: A

QUESTION 7
Which three items are Cisco best-practice recommendations for securing a network? (Choose three.)
A. Deploy HIPS software on all end-user workstations.
B. Routinely apply patches to operating systems and applications.
C. Disable unneeded services and ports on hosts.
D. Require strong passwords, and enable password expiration.

Answer: BCD


QUESTION 8
For the following attempts, which one is to ensure that no one employee becomes a pervasive security threat, that data can be recovered from backups, and that information system changes do not compromise a system's security?
A. Disaster recovery
B. Strategic security planning
C. Implementation security
D. Operations security
Answer: D


QUESTION 9
For the following options ,which one accurately matches the CLI command(s) to the equivalent SDM wizard that performs similar configuration functions?
A.setup exec command and the SDM Security Audit wizard B.auto secure exec command and the SDM One-Step Lockdown wizard C.aaa configuration commands and the SDM Basic Firewall wizard D.Cisco Common Classification Policy Language configuration commands and the SDM Site-to-Site VPN
wizard
Answer: B

QUESTION 10
Which three options are network evaluation techniques? (Choose three.)
A. Scanning a network for active IP addresses and open ports on those IP addresses
B. Using password-cracking utilities
C. Performing end-user training on the use of antispyware software
D. Performing virus scans
Answer: ABD
QUESTION 11
Which is the main difference between host-based and network-based intrusion prevention?

A.Network-based IPS is better suited for inspection of SSL and TLS encrypted data flows.
B.Host-based IPS can work in promiscuous mode or inline mode.
C.Network-based IPS can provide protection to desktops and servers without the need of installing specialized software on the end hosts and servers.
D.Host-based IPS deployment requires less planning than network-based IPS.
Answer: C


QUESTION 12
Which one is the most important based on the following common elements of a network design?
A. Business needs
B. Best practices
C. Risk analysis
D. Security policy
Answer: A


QUESTION 13
Given the exhibit below. You are a network manager of your company. You are reading your Syslog server reports. On the basis of the Syslog message shown, which two descriptions are correct? (Choose two.)

A.This message is a level 5 notification message. B.This message is unimportant and can be ignored. C.This is a normal system-generated information message and does not require further investigation. D.Service timestamps have been globally enabled.
Answer: AD


QUESTION 14
Examine the following items, which one offers a variety of security solutions, including firewall, IPS, VPN, antispyware, antivirus, and antiphishing features?
A. Cisco 4200 series IPS appliance
B. Cisco ASA 5500 series security appliance

C. Cisco IOS router
D. Cisco PIX 500 series security appliance
Answer: B


QUESTION 15
The enable secret password appears as an MD5 hash in a router's configuration file, whereas the enable password is not hashed (or encrypted, if the password-encryption service is not enabled). What is the reason that Cisco still support the use of both enable secret and enable passwords in a router's configuration?
A.The enable password is used for IKE Phase I, whereas the enable secret password is used for IKE Phase II. B.The enable password is considered to be a router's public key, whereas the enable secret password is considered to be a router's private key. C.Because the enable secret password is a hash, it cannot be decrypted. Therefore, the enable password is used to match the password that was entered, and the enable secret is used to verify that the enable password has not been modified since the hash was generated. D.The enable password is present for backward compatibility.
Answer: D


QUESTION 16
How does CLI view differ from a privilege level?
A.A CLI view supports only commands configured for that specific view, whereas a privilege level supports commands available to that level and all the lower levels.
B.A CLI view supports only monitoring commands, whereas a privilege level allows a user to make changes to an IOS configuration.
C.A CLI view and a privilege level perform the same function. However, a CLI view is used on a Catalyst switch, whereas a privilege level is used on an IOS router.
D.A CLI view can function without a AAA configuration, whereas a privilege level requires AAA to be configured.
Answer: A

QUESTION 17
When configuring Cisco IOS login enhancements for virtual connections, what is the "quiet period"?
A.A period of time when no one is attempting to log in

B.The period of time in which virtual logins are blocked as security services fully initialize
C.The period of time in which virtual login attempts are blocked, following repeated failed login attempts D.The period of time between successive login attempts
Answer: C
QUESTION 18
Which result is of securing the Cisco IOS image by use of the Cisco IOS image resilience feature?
A. When the router boots up, the Cisco IOS image will be loaded from a secured FTP location.
B. The Cisco IOS image file will not be visible in the output from the show flash command.
C. The show version command will not show the Cisco IOS image file location.
D. The running Cisco IOS image will be encrypted and then automatically backed up to a TFTP server.

Answer: B
QUESTION 19
Which three statements are valid SDM configuration wizards? (Choose three.)
A. Security Audit
B. VPN
C. STP
D. NAT

Answer: ABD
QUESTION 20
How do you define the authentication method that will be used with AAA?
A. With a method list
B. With the method command
C. With the method aaa command
D. With a method statement
Answer: A
QUESTION 21
What is the objective of the aaa authentication login console-in local command?

A.It specifies the login authorization method list named console-in using the local RADIUS username-password database.
B.It specifies the login authorization method list named console-in using the local username-password database on the router.
C.It specifies the login authentication method list named console-in using the local user database on the router.
D.It specifies the login authentication list named console-in using the local username-password database on the router.

Answer: C
QUESTION 22
Which description is true about the show login command output displayed in the exhibit?

A.All logins from any sources are blocked for another 193 seconds.
B.The login block-for command is configured to block login hosts for 93 seconds.
C.When the router goes into quiet mode, any host is permitted to access the router via Telnet, SSH, and HTTP, since the quiet-mode access list has not been configured.
D.Three or more login requests have failed within the last 100 seconds.

Answer: D
QUESTION 23
Which one of the following commands can be used to enable AAA authentication to determine if a user can access the privilege command level?
A. aaa authentication enable default local
B. aaa authentication enable level

C. aaa authentication enable method default
D. aaa authentication enable default

Answer: D
QUESTION 24
Which two ports are used with RADIUS authentication and authorization?(Choose two.)
A. TCP port 2002
B. UDP port 2000
C. UDP port 1645
D. UDP port 1812

Answer: CD
QUESTION 25
For the following items, which management topology keeps management traffic isolated from production traffic?
A. OOB
B. SAFE
C. MARS
D. OTP

Answer: A
QUESTION 26
What are four methods used by hackers? (Choose four.)
A. social engineering attack
B. Trojan horse attack
C. front door attacks
D. buffer Unicode attack
E. privilege escalation attack
F. footprint analysis attack
Answer: ABEF QUESTION 27

Information about a managed device's resources and activity is defined by a series of objects. What defines the structure of these management objects?
A. FIB
B. LDAP
C. CEF
D. MIB

Answer: D
QUESTION 28
After enabling port security on a Cisco Catalyst switch, what is the default action when the configured maximum of allowed MAC addresses value is exceeded?
A. The port is shut down.
B. The port's violation mode is set to restrict.
C. The MAC address table is cleared and the new MAC address is entered into the table.
D. The port remains enabled, but bandwidth is throttled until old MAC addresses are aged out.

Answer: A
QUESTION 29
When configuring SSH, which is the Cisco minimum recommended modulus value?
A. 2048 bits
B. 256 bits
C. 1024 bits
D. 512 bits

Answer: C
QUESTION 30
When using the Cisco SDM Quick Setup Siteto-Site VPN wizard, which three parameters do you configure? (Choose three.)
A. Interface for the VPN connection
B. IP address for the remote peer
C. Transform set for the IPsec tunnel

D. Source interface where encrypted traffic originates

Answer: ABD
QUESTION 31
If you click the Configure button along the top of Cisco SDM's graphical interface,which Tasks button permits you to configure such features as SSH, NTP, SNMP, and syslog?
A. Additional Tasks
B. Security Audit
C. Intrusion Prevention
D. Interfaces and Connections

Answer: A
QUESTION 32
Which item is correct regarding Cisco IOS IPS on Cisco IOS Release 12.4(11)T and later ?
A. uses Cisco IPS 5.x signature format
B. supports SDEE, SYSLOG, and SNMP for sending Cisco IPS alerts
C. requires the Basic or Advanced Signature Definition File
D. uses the built-in signatures that come with the Cisco IOS image as backup

Answer: A
QUESTION 33
Examine the following options , which Spanning Tree Protocol (STP) protection mechanism disables a switch port if the port receives a Bridge Protocol Data Unit (BPDU)?
A. PortFast
B. BPDU Guard
C. UplinkFast
D. Root Guard
Answer: B
QUESTION 34
For the following options, which feature is the foundation of Cisco Self-Defending Network technology?

A. policy management
B. secure connectivity
C. threat control and containment
D. secure network platform

Answer: D
QUESTION 35
If a switch is working in the fail-open mode, what will happen when the switch's CAM table fills to capacity and a new frame arrives?
A. The switch sends a NACK segment to the frame's source MAC address.
B. A copy of the frame is forwarded out all switch ports other than the port the frame was received on.
C. The frame is dropped.
D. The frame is transmitted on the native VLAN.

Answer: B
QUESTION 36
Which kind of table will be used by most firewalls today to keep track of the connections through the firewall?
A. queuing
B. netflow
C. dynamic ACL
D. reflexive ACL
E. state

Answer: E
QUESTION 37
Which type of MAC address is dynamically learned by a switch port and then added to the switch's running configuration?
A. Pervasive secure MAC address
B. Static secure MAC address
C. Sticky secure MAC address
D. Dynamic secure MAC address


Answer: C
QUESTION 38
In an IEEE 802.1x deployment, between which two devices EAPOL messages typically are sent?
A. Between the RADIUS server and the authenticator
B. Between the authenticator and the authentication server
C. Between the supplicant and the authentication server
D. Between the supplicant and the authenticator

Answer: D
QUESTION 39
Which one of the Cisco IOS commands can be used to verify that either the Cisco IOS image, the configuration files, or both have been properly backed up and secured?
A. show flash
B. show secure bootset
C. show archive
D. show file systems

Answer: B
QUESTION 40
Which item is the great majority of software vulnerabilities that have been discovered?
A. Stack vulnerabilities
B. Software overflows
C. Heap overflows
D. Buffer overflows
Answer: D
QUESTION 41
Which type of intrusion prevention technology will be primarily used by the Cisco IPS security appliances?
A. rule-based
B. protocol analysis-based

C. signature-based
D. profile-based

Answer: C
QUESTION 42
What will be enabled by the scanning technology-The Dynamic Vector Streaming (DVS)?
A. Firmware-level virus detection
B. Layer 4 virus detection
C. Signature-based spyware filtering
D. Signature-based virus filtering

Answer: C
QUESTION 43
What is the purpose of the secure boot-config global configuration?
OR
What does the secure boot-config global configuration accomplish?
A. backs up the Cisco IOS image from flash to a TFTP server
B. enables Cisco IOS image resilience
C. takes a snapshot of the router running configuration and securely archives it in persistent storage
D. stores a secured copy of the Cisco IOS image in its persistent storage
Answer: C
QUESTION 44
What Cisco Security Agent Interceptor is in charge of intercepting all read/write requests to the rc files in UNIX?
A. Network interceptor
B. Configuration interceptor
C. Execution space interceptor
D. File system interceptor
Answer: B
QUESTION 45

Which name is of the e-mail traffic monitoring service that underlies that architecture of IronPort?
A. IronPort M-Series
B. E-Base
C. TrafMon
D. SenderBase

Answer: D
QUESTION 46
Based on the username global configuration mode command displayed in the exhibit. What does the option secret 5 indicate about the enable secret password?

A. It is encrypted using DH group 5.
B. It is hashed using SHA.
C. It is hashed using MD5.
D. It is encrypted using a proprietary Cisco encryption algorithm.

Answer: C
QUESTION 47
Which statement is not a reason for an organization to incorporate a SAN in its enterprise infrastructure?
A. To increase the performance of long-distance replication, backup, and recovery
B. To decrease the threat of viruses and worm attacks against data storage devices
C. To decrease both capital and operating expenses associated with data storage
D. To meet changing business priorities, applications, and revenue growth

Answer: B
QUESTION 48
On the basis of the show policy-map type inspect zone-pair session command output provided in the exhibit.What can be determined about this Cisco IOS zone based firewall policy?


A.This is an outbound policy (applied to traffic sourced from the more secured zone destined to the less secured zone).
B.All packets will be dropped since the class-default traffic class is matching all traffic.
C.This is an inbound policy (applied to traffic sourced from the less secured zone destined to the more secured zone).
D.Stateful packet inspection will be applied only to HTTP packets that also match ACL 110.

Answer: D
QUESTION 49
Which protocol will use a LUN as a way to differentiate the individual disk drives that comprise a target device?
A. iSCSI
B. ATA
C. SCSI
D. HBA
Answer: C QUESTION 50

What should be enabled before any user views can be created during role-based CLI configuration?
OR
During role-based CLI configuration, what must be enabled before any user views can be created?
A. usernames and passwords
B. secret password for the root user
C. aaa new-model command
D. multiple privilege levels

Answer: C
QUESTION 51
For the following statements, which one is perceived as a drawback of implementing Fibre Channel Authentication Protocol (FCAP)?
A. It is restricted in size to only three segments.
B. It requires the implementation of IKE.
C. It relies on an underlying Public Key Infrastructure (PKI).
D. It requires the use of netBT as the network protocol.

Answer: C
QUESTION 52
Which two primary port authentication protocols are used with VSANs? (Choose two.)
A. ESP
B. CHAP
C. DHCHAP
D. SPAP
Answer: BC
QUESTION 53
Which statement best describes Cisco IOS Zone-Based Policy Firewall?
OR
Which statement about Cisco IOS Zone-Based Policy Firewall is true?

A.A router interface can belong to multiple zones. B.The pass action works in only one direction. C.Policy maps are used to classify traffic into different traffic classes, and class maps are used to assign action
to the traffic classes.
D.A zone-pair is bidirectional because it specifies traffic flowing among the interfaces within the zone-pair in both directions.

Answer: B
QUESTION 54
Which VoIP components can permit or deny a call attempt on the basis of a network's available bandwidth?
A. MCU
B. Gatekeeper
C. Application server
D. Gateway

Answer: B
QUESTION 55
Which statement is true about vishing?
A.Influencing users to forward a call to a toll number (for example, a long distance or international number) B.Influencing users to provide personal information over the phone C.Using an inside facilitator to intentionally forward a call to a toll number (for example, a long distance or
international number) D.Influencing users to provide personal information over a web page

Answer: B
QUESTION 56
You work as a network engineer, do you know an IPsec tunnel is negotiated within the protection of which type of tunnel?
A. GRE tunnel
B. L2TP tunnel
C. L2F tunnel
D. ISAKMP tunnel


Answer: D
QUESTION 57
Which type of firewall is needed to open appropriate UDP ports required for RTP streams?
A. Proxy firewall
B. Packet filtering firewall
C. Stateful firewall
D. Stateless firewall

Answer: C
QUESTION 58
Which two statements are correct regarding a Cisco IP phone's web access feature? (Choose two.)
A. It is enabled by default.
B. It uses HTTPS.
C. It can provide IP address information about other servers in the network.
D. It requires login credentials, based on the UCM user database.

Answer: AC
QUESTION 59
Which option ensures that data is not modified in transit?
A. Authentication
B. Integrity
C. Authorization
D. Confidentiality
Answer: B
QUESTION 60
What is a static packet-filtering firewall used for?
A.It analyzes network traffic at the network and transport protocol layers. B.It validates the fact that a packet is either a connection request or a data packet belonging to a connection. C.It keeps track of the actual communication process through the use of a state table.

D.It evaluates network packets for valid data at the application layer before allowing connections.

Answer: A
QUESTION 61
Which information is stored in the stateful session flow table while using a stateful firewall?
A.all TCP and UDP header information only
B.the source and destination IP addresses, port numbers, TCP sequencing information, and additional flags for each TCP or UDP connection associated with a particular session
C.the outbound and inbound access rules (ACL entries)
D.the inside private IP address and the translated inside global IP address

Answer: B
QUESTION 62
Which firewall best practices can help mitigate worm and other automated attacks?
A. Restrict access to firewalls
B. Segment security zones
C. Use logs and alerts
D. Set connection limits
Answer: D
QUESTION 63
Refer to Cisco IOS Zone-Based Policy Firewall, where will the inspection policy be applied?
A. to the interface
B. to the zone-pair
C. to the global service policy
D. to the zone
Answer: B
QUESTION 64
Which statement best describes the Turbo ACL feature? (Choose all that apply.)

A.The Turbo ACL feature processes ACLs into lookup tables for greater efficiency. B.The Turbo ACL feature leads to increased latency, because the time it takes to match the packet is variable. C.The Turbo ACL feature leads to reduced latency, because the time it takes to match the packet is fixed and
consistent. D.Turbo ACLs increase the CPU load by matching the packet to a predetermined list.

Answer: AC
QUESTION 65
Which statement best describes configuring access control lists to control Telnet traffic destined to the router itself?
A.The ACL must be applied to each vty line individually. B.The ACL should be applied to all vty lines in the in direction to prevent an unwanted user from connecting to
an unsecured port. C.The ACL is applied to the Telnet port with the ip access-group command. D.The ACL applied to the vty lines has no in or out option like ACL being applied to an interface.

Answer: B
QUESTION 66
Which two actions can be configured to allow traffic to traverse an interface when zone-based security is being employed? (Choose two.)
A. Flow
B. Inspect
C. Pass
D. Allow
Answer: BC
QUESTION 67
When configuring role-based CLI on a Cisco router, which action will be taken first?
A.Create a parser view called "root view." B.Log in to the router as the root user. C.Enable role-based CLI globally on the router using the privileged EXEC mode Cisco IOS command. D.Enable the root view on the router.


Answer: D
QUESTION 68
Which key method is used to detect and prevent attacks by use of IDS and/or IPS technologies?
A. Signature-based detection
B. Anomaly-based detection
C. Honey pot detection
D. Policy-based detection

Answer: A
QUESTION 69
Which statement is correct regarding the aaa configurations based on the exhibit provided?

A.The authentication method list used by the console port is named test.
B.The authentication method list used by the vty port is named test.
C.If the TACACS+ AAA server is not available, console access to the router can be authenticated using the local database.
D.If the TACACS+ AAA server is not available, no users will be able to establish a Telnet session with the router.

Answer: B
QUESTION 70
Based on the following items, which two types of interfaces are found on all network-based IPS sensors? (Choose two.)
A. Loopback interface
B. Monitoring interface
C. Command and control interface

D. Management interface

Answer: BC
QUESTION 71
Which feature is a potential security weakness of a traditional stateful firewall?
A. It cannot ensure each TCP connection follows a legitimate TCP three-way handshake.
B. It cannot detect application-layer attacks.
C. It cannot support UDP flows.
D. The status of TCP sessions is retained in the state table after the sessions terminate.

Answer: B
QUESTION 72
With which three tasks does the IPS Policies Wizard help you? (Choose three.)
A. Selecting the interface to which the IPS rule will be applied
B. Selecting the direction of traffic that will be inspected
C. Selecting the inspection policy that will be applied to the interface
D. Selecting the Signature Definition File (SDF) that the router will use

Answer: ABD
QUESTION 73
What is the objective of Diffie-Hellman?
A. used for asymmetric public key encryption
B. used between the initiator and the responder to establish a basic security policy
C. used to verify the identity of the peer
D. used to establish a symmetric shared key via a public key exchange process

Answer: D
QUESTION 74
Examine the following options ,when editing global IPS settings, which one determines if the IOS-based IPS feature will drop or permit traffic for a particular IPS signature engine while a new signature for that engine is being compiled?

A. Enable Engine Fail Closed
B. Enable Fail Opened
C. Enable Signature Default
D. Enable Default IOS Signature

Answer: A
QUESTION 75
Which description about asymmetric encryption algorithms is correct?
A. They use different keys for decryption but the same key for encryption of data.
B. They use the same key for encryption and decryption of data.
C. They use different keys for encryption and decryption of data.
D. They use the same key for decryption but different keys for encryption of data.

Answer: C
QUESTION 76
Regarding constructing a good encryption algorithm, what does creating an avalanche effect indicate?
A. Changing only a few bits of a plain-text message causes the ciphertext to be completely different.
B. Changing only a few bits of a ciphertext message causes the plain text to be completely different.
C. Altering the key length causes the plain text to be completely different.
D. Altering the key length causes the ciphertext to be completely different.

Answer: A
QUESTION 77
Which one of the aaa accounting commands can be used to enable logging of both the start and stop records for user terminal sessions on the router?
A. aaa accounting connection start-stop tacacs+
B. aaa accounting network start-stop tacacs+
C. aaa accounting exec start-stop tacacs+
D. aaa accounting system start-stop tacacs+
Answer: C QUESTION 78

Stream ciphers run on which of the following?
A. Individual blocks, one at a time, with the transformations varying during the encryption
B. Individual digits, one at a time, with the transformations varying during the encryption
C. Fixed-length groups of digits called blocks
D. Fixed-length groups of bits called blocks

Answer: B
QUESTION 79
Which description is correct based on the exhibit and partial configuration?

A.All traffic from network 10.0.0.0 will be permitted.
B.This ACL will prevent any host on the Internet from spoofing the inside network address as the source address for packets coming into the router from the Internet.
C.Access-list 101 will prevent address spoofing from interface E0.
D.All traffic destined for network 172.16.150.0 will be denied due to the implicit deny all.

Answer: C QUESTION 80

Which description is true about ECB mode?
A.ECB mode uses the same 64-bit key to serially encrypt each 56-bit plain-text block.
B.In ECB mode, each 56-bit plain-text block is exclusive ORed (XORed) bitwise with the previous ciphertext block.
C.ECB mode uses the same 56-bit key to serially encrypt each 64-bit plain-text block.
D.In ECB mode, each 64-bit plain-text block is exclusive ORed (XORed) bitwise with the previous ciphertext
block.

Answer: C
QUESTION 81
For the following items ,which one can be used to authenticate the IPsec peers during IKE Phase 1?
A. XAUTH
B. pre-shared key
C. integrity check value
D. Diffie-Hellman Nonce

Answer: B
QUESTION 82
In a brute-force attack, what percentage of the keyspace must an attacker generally search through until he or she finds the key that decrypts the data?
A. Roughly 66 percent
B. Roughly 10 percent
C. Roughly 75 percent
D. Roughly 50 percent
Answer: D
QUESTION 83
What will be disabled as a result of the no service password-recovery command?
A. password encryption service
B. ROMMON

C. changes to the config-register setting
D. the xmodem privilege EXEC mode command to recover the Cisco IOS image

Answer: B
QUESTION 84
Which example is of a function intended for cryptographic hashing?
A. SHA-135
B. MD65
C. XR12
D. MD5

Answer: D
QUESTION 85
Which one of the following items may be added to a password stored in MD5 to make it more secure?
A. Rainbow table
B. Cryptotext
C. Ciphertext
D. Salt

Answer: D
QUESTION 86
What is the MD5 algorithm used for?
A. takes a variable-length message and produces a 168-bit message digest
B. takes a fixed-length message and produces a 128-bit message digest
C. takes a variable-length message and produces a 128-bit message digest
D. takes a message less than 2^64 bits as input and produces a 160-bit message digest
Answer: C
QUESTION 87
Which algorithm was the first to be found suitable for both digital signing and encryption?

A. SHA-1
B. MD5
C. HMAC
D. RSA

Answer: D
QUESTION 88
Examine the following options, which access list will permit HTTP traffic sourced from host 10.1.129.100 port 3030 destined to host 192.168.1.10?
A. access-list 101 permit tcp 10.1.129.0 0.0.0.255 eq www 192.168.1.10 0.0.0.0 eq www
B. access-list 101 permit tcp 10.1.128.0 0.0.1.255 eq 3030 192.168.1.0 0.0.0.15 eq www
C. access-list 101 permit tcp host 192.168.1.10 eq 80 10.1.0.0 0.0.255.255 eq 3030
D. access-list 101 permit tcp any eq 3030

Answer: B
QUESTION 89
Observe the following options carefully, which two attacks focus on RSA? (Choose all that apply.)
A. DDoS attack
B. BPA attack
C. Adaptive chosen ciphertext attack
D. Man-in-the-middle attack

Answer: BC
QUESTION 90
A standard access control list has been configured on a router and applied to interface Serial 0 in an outbound direction. No ACL is applied to Interface Serial 1 on the same router. What will happen when traffic being filtered by the access list does not match the configured ACL statements for Serial 0?
A.The source IP address is checked, and, if a match is not found, traffic is routed out interface Serial 1. B.The resulting action is determined by the destination IP address. C.The resulting action is determined by the destination IP address and port number. D.The traffic is dropped.


Answer: D
QUESTION 91
Before a Diffie-Hellman exchange may begin, the two parties involved must agree on what?
A. Two nonsecret keys
B. Two secret numbers
C. Two secret keys
D. Two nonsecret numbers

Answer: D
QUESTION 92
Which three are distinctions between asymmetric and symmetric algorithms? (Choose all that apply.)
A. Asymmetric algorithms are based on more complex mathematical computations.
B. Only symmetric algorithms have a key exchange technology built in.
C. Only asymmetric algorithms have a key exchange technology built in.
D. Asymmetric algorithms are used quite often as key exchange protocols for symmetric algorithms.

Answer: ACD
QUESTION 93
For the following statements, which one is the strongest symmetrical encryption algorithm?
A. 3DES
B. DES
C. AES
D. Diffie-Hellman
Answer: C
QUESTION 94
Which statement is true about a certificate authority (CA)?
A. A trusted third party responsible for signing the private keys of entities in a PKIbased system
B. A trusted third party responsible for signing the public keys of entities in a PKIbased system
C. An entity responsible for registering the private key encryption used in a PKI D. An agency responsible for granting and revoking public-private key pairs


Answer: B
QUESTION 95
Which location will be recommended for extended or extended named ACLs?
A.a location as close to the destination traffic as possible B.an intermediate location to filter as much traffic as possible C.when using the established keyword, a location close to the destination point to ensure that return traffic is
allowed
D.a location as close to the source traffic as possible

Answer: D
QUESTION 96
Which Public Key Cryptographic Standards (PKCS) defines the syntax for encrypted messages and messages with digital signatures?
A. PKCS #12
B. PKCS #10
C. PKCS #8
D. PKCS #7

Answer: D
QUESTION 97
For the following items, which one acts as a VPN termination device and is located at a primary network location?
A. Headend VPN device
B. Tunnel
C. Broadband service
D. VPN access device
Answer: A
QUESTION 98

Look at the exhibit:
You suspect an attacker in your network has configured a rogue layer 2 device to intercept traffic from multiple VLANS, thereby allowing the attacker to capture potentially sensitive data. Which two methods will help to mitigate this type of activity? (Choose two.)
A. Turn off all trunk ports and manually configure each VLAN as required on each port
B. Disable DTP on ports that require trunking
C. Secure the native VLAN, VLAN 1 with encryption
D. Set the native VALN on the trunk ports to an unused VLAN
E. Place unused active ports in an unused VLAN

Answer: BD
QUESTION 99
When configuring AAA login authentication on CISCO routers, which two authentication methods should be used as the final method to ensure that the administrator can still log in to the router in case the external AAA server fails? (Choose two)
A. krb5
B. local
C. enable
D. group RADIUS
E. group TACAS+

Answer: BC
QUESTION 100
Which two protocols enable Cisco SDM to pull IPS alerts from a CISCO ISR router? (Choose two.)
A. FTP
B. HTTPS
C. TFTP
D. SSH
E. Syslog
F. SDEE
Answer: BF
QUESTION 101

When configuring Cisco IOS Zone-Based Policy Firewall, what are the three actions that can be applied to a traffic class? (Choose three.)
A. Pass
B. Police
C. Inspect
D. Drop
E. Queue
F. Shape

Answer: ACD
QUESTION 102
Which three statements about applying access control lists to a Cisco router are true? (Choose three.)
A.Place more specific ACL entries at the top of the ACL.
B.ACLs always search for the most speeific entry before taking any filtering action.
C.Router-generated packets cannot be filtered by ACls on the router.
D.Place generic ACL entries at the top of the ACL to filter general traffic and thereby reduce "noise" on the network.
E.IF an access list is applied but is not configured, all traffic will pass.

Answer: ACE
QUESTION 103
Which two functions are required for IPsec operation? (Choose two.)
A. using AH protocols for encryption and authentication
B. using SHA for encryption
C. using Diffie-Hellman to establish a shared-secret key
D. using PKI for pre-shared-key authentication
E. using IKE to negotiate the SA
Answer: CE
QUESTION 104
What is the goal of an overall security challenge when planning a security strategy?
A.to harden all exterior-facing networks components

B.to install firewalls at all critical points in the network
C.to find a balance between the need to open networks to support evolving business requirements and to need to inform
D.to educate employees to be on the lookout for suspicious behaviour

Answer: C
QUESTION 105
Which threat are the most serious?
A. inside threats
B. outside threats
C. unknown threats
D. reconnaissance threats

Answer: A
QUESTION 106
Network security aims to provide which three key services? (choose three)
A. data integrity
B. data strategy
C. data & system availability
D. data mining
E. data storage
F. data confidentiality
Answer: ACF
QUESTION 107
Which option is the term for a weakness in a system or its design that can be exploited by a threat
A. a vulnerability
B. a risk
C. an exploit
D. an attack
E. a joke
Answer: A QUESTION 108

Which option is the term for the likelihood that a particular threat using a specific attack will exploit particular vulnerability of a system that results in an undesirable consequence?
A. a vulnerability
B. a risk
C. an exploit
D. an attack
E. a joke

Answer: B
QUESTION 109
Which option is the term for what happens when a computer code is developed to take advantage of vulnerability? For example, suppose that a vulnerability exists in a piece of software, but nobody knows about this vulnerability.
A. a vulnerability
B. a risk
C. an exploit
D. an attack
E. a joke
Answer: C
QUESTION 110
What is the first step you should take when considering securing your network?
A. install a firewall
B. install an intrusion prevention system
C. update servers and user PCs with the latest patches
D. Develop a security policy
E. go drink beer and don?t worry about it
Answer: D QUESTION 111

Which option is a key principal of the Cisco Self-Defending Network strategy?
A. security is static and should prevent most know attack on the network
B. the self-defending network should be the key point of your security policy
C. integrate security throughout the existing infracture
D. upper management is ultimately responsible for policy implementation

Answer: C
QUESTION 112
Which three option are areas of router security?
A. physical security
B. access control list security
C. zone-base firewall security
D. operating system security
E. router hardening
F. cisco IOS-IPS security

Answer: ADE
QUESTION 113
You have several operating groups in your enterprise that require different access restrictions to the routers to perform their jobs roles. These groups range from Help Desk personnel to advanced troubleshooters. What is one methodology for controlling access rights to the router in these situation?
A. configure ACLs to control access for these different groups
B. configure multiple privilege level access
C. implement syslogging to monitor the activities of these groups
D. configure TACACS+ to perform scalable authentication
Answer: B
QUESTION 114
Which of these is a GUI tool for performing security configuration on Cisco routers?
A. security appliance device manager
B. cisco CLI configuration management tool

C. cisco security device manager
D. cisco security manager

Answer: C
QUESTION 115
When implementing network security, what is an important configuration task that you should perform to assist in correlating network and security events?
A. configure network time protocol
B. configure synchronized syslog reporting
C. configure a common repository of all network events for ease of monitoring
D. configure an automated network monitoring system for event correlation

Answer: A
QUESTION 116
Which of these options is a Cisco IOS feature that lets you more easily configure security features on your router?
A. cisco self-defending network
B. implementing AAA command authorization
C. the auto secure CLI command
D. performing a security audit via SDM

Answer: C
QUESTION 117
Which three of these options are some of the best practices when you implement an effective firewall security policy? (choose three)
A. position firewalls at a strategic inside locations to help mitigate nontechnical attacks
B. configure logging to capture all events for forensic purposes
C. use firewalls as a primary security defense; other security measures and devices shoulde be implemented to enhance your network security
D. position firewalls at key security boundeeries
E. deny all traffic by default and permit only necessary services
Answer: CDE QUESTION 118

Which option correctly defines asymmetric encryption?
A. uses the same keys to encrypt and decrypt data
B. uses MD5 hashing algorithms for digital signage encryption
C. uses different keys to encrypt and decrypt data
D. uses SHA-1 hashing algorithms for digital signage encryption

Answer: C
QUESTION 119
Which option is a desirable feature of using symmetric encryption algorithms?
A. they are often used for wire-speed encryption in data networks
B. they are based on complex mathematical operations and can easily be accelerated by hardware
C. they offer simple key management properties
D. they are best used for one-time encryption needs

Answer: A
QUESTION 120
Which option is true of using cryptographic hashes?
A. they are easily reversed to decipher the message context
B. they convert arbitrary data into fixed length digits
C. they are based on a two-way mathematical function
D. they are used for encrypting bulk data communications
Answer: B
QUESTION 121
Which option is true of intrusion prevention systems?
A. they operate in promiscuous mode
B. they operate in inline mode
C. they have no potential impact on the data segment being monitored
D. they are more vulnerable to evasion techniques than IDS


Answer: B
QUESTION 122
Which statement is true when using zone-based firewalls on a Cisco router?
A.policies are applied to traffic moving between zones, not between interfaces
B.the firewalls can be configured simultaneously on the same interface as classic CBAC using the ip inspect CLI command
C.interface ACLs are applied before zone-based policy firewalls when they are applied outbond
D.when configuring with the ?PASS? action, stateful inspection is applied to all traffic passing between the
configured zones

Answer: A
QUESTION 123
From what configuration mode would you enter the set peer ip-address command to specify the IP address of an IPsec peer?
A. Transform set configuration mode
B. Crypto map configuration mode
C. ISAKMP configuration mode
D. Interface configuration mode
Answer: B
QUESTION 124
What two site-to-site VPN wizards are available in the Cisco SDM interface? (Choose two.)
A. Easy VPN Setup
B. Quick Setup
C. Step-by-Step
D. DMVPN Setup
Answer: BC
QUESTION 125
What command displays all existing IPsec security associations (SA)?

A. show crypto isakmp sa
B. show crypto ipsec sa
C. show crypto ike active
D. show crypto sa active

Answer: B
QUESTION 126
Which two statements are true about the differences between IDS and IPS? (Choose two.)
A. IPS operates in promiscuous mode.
B. IPS receives a copy of the traffic to be analyzed.
C. IPS operates in inline mode.
D. IDS receives a copy of the traffic to be analyzed.

Answer: CD
QUESTION 127
What form of attack are all algorithms susceptible to?
A. Meet-in-the-middle
B. Spoofing
C. Stream cipher
D. Brute-force
Answer: D
QUESTION 128
Which type of cipher achieves security by rearranging the letters in a string of text?
A. Vigen��re cipher
B. Stream cipher
C. Transposition cipher
D. Block cipher
Answer: C
QUESTION 129

Which of the following are techniques used by symmetric encryption cryptography? (Choose all that apply.)
A. Block ciphers
B. Message Authentication Codes (MAC)
C. One-time pad
D. Stream ciphers
E. Vigen��re cipher

Answer: ABD
QUESTION 130
DES typically operates in block mode, where it encrypts data in what size blocks?
A. 56-bit blocks
B. 40-bit blocks
C. 128-bit blocks
D. 64-bit blocks

Answer: D
QUESTION 131
What method does 3DES use to encrypt plain text?
A. 3DES-EDE
B. EDE-3DES
C. 3DES-AES
D. AES-3DES
Answer: A
QUESTION 132
Which of the following is not considered a trustworthy symmetric encryption algorithm?
A. 3DES
B. IDEA
C. EDE
D. AES
Answer: C QUESTION 133

On the basis of the description of SSL-based VPN, place the correct descriptions in the proper locations.

Answer:

QUESTION 134
Which three common examples are of AAA implementation on Cisco routers? Please place the correct descriptions in the proper locations.


Answer:


QUESTION 135
Drag two characteristics of the SDM Security Audit wizard on the above to the list on the below.


Answer:


QUESTION 136
On the basis of the Cisco IOS Zone-Based Policy Firewall, by default, which three types of traffic are permitted by the router when some interfaces of the routers are assigned to a zone? Drag three proper characterizations on the above to the list on the below.

Answer:


QUESTION 137
Drag three proper statements about the IPsec protocol on the above to the list on the below.


Answer:


QUESTION 138
Drop and drog. Match the descriptions on the above with the IKE phases on the below.


Answer:


QUESTION 139
Drag the result on the left to the corresponding attack method on the right.

Answer:


QUESTION 140
On the basis of the description of SSL-based VPN, place the correct descriptions in the proper locations.


Answer:
QUESTION 141 Drag & Drop



Answer:

QUESTION 142
Scenario: Next Gen University main campus is located in Santa Cruz. The University has recently establisheci various remote campuses offening -lerning services. The UnverIty is using IPec VPN connectivity between its main and remote campus Phoenix (PHX), Newadla (ND). Sacremento (SAC). As a recent addition to The IT/Networking team. You have beeni tasked to document the IPsec VPN configurations to the remote campuses using the Cisco Ruler and SDM utility. Using the SDM output from VPN Tasks under the Configure tab, annwer these quetions
Cisco SDM 5.0:



A.1. Which one of these statements is correct in regards to Next Gen University Psec tunnel between its Santa

Cruz main campus and its PHX remote campus?
A: It is using IPsec tunnel mode A&S encryption and SHA HMAC Integrity Check.
B: It is using IPsec tunnel mode. 3DES encryption and SHA HMAC Integrity Check.
C: It Ia using IPsec tunnel mode to protect the traffic between the 10.10. 10.0/24 and the 10.253.0/24 sbnet,
D: It is using digital certificate authenticate between the IPsec peers and DH group 2
E: It Is using pre-shared key to ahentlcate beteen the IPsec pens and OH group 5
F: The Santa Cruz main campus is the Easy VPN server and the PHX remote campus is easy VPN remote.
Answer: C
2. Which of these is used to define which traffic will be protected by IPsec between the Next Gen University Santa Cruz main campus and its SAC remote campus?
A: ACL 174
B: ACL 168
C: ACL 151
D: ESP-3DES.SHAI transform set
E: ESP-3DES-SHA2 transform set
F: IKE Phase
Answer: A
3. The IPsec tunnel to the SAC remote campus terminates at which IP address, and what is the protected subnet behind the SAC remote campus router? (Choose two.)
A: 192,168288
B: 192.168.5.28
C: 192.168.8.97
D: 10.2.53.0/124
E: 10.5.64.0/124
F: 10.8.74.0/124
Answer: C, F
4. Which one of these statements is correct in regards to Next Gen University IPsec tunnel between its Santa Cruz main campus and its SAC remote campus?
A: The SAC remote campus remote router is using dynamic IP address; therefore, the Santa
B: Cruz router is using a dynamic crypto map.
C: Dead Peer Detection (DPD) is used to monitor the IPsec tunnel, so if there is no traffic traversing between the two sites, the IPsec tunnel will disconnect.
D: Tunnel mode is used: therefore, a GRE tunnel interface will be configured.

E: Only the ESP protocol is being used: AH is not being used.
Answer: D
QUESTION 143
Refer to the exhibit. You are the network security administrator responsible for router security. Your network uses internal IP addressing according to RFC 1918 specifications. From the default rules shown, which access control list would prevent IP address spoofing of these internal networks?

A. SDM_Default_196
B. SDM_Default_197
C. SDM_Default_198
D. SDM_Default_199

Answer: C
QUESTION 144
Refer to the exhibit. Based on the VPN connection shown, which statement is true?


A. Traffic that matches access list 103 will be protected.
B. This VPN configuration will not work because the tunnel IP and peer IP are the same.
C. The tunnel is down as result of being a static rule. It should be configured as a Dynamic IPsec policy.
D. The tunnel is down because the transform set needs to include the Authentication Header parameter.

Answer: A
QUESTION 145
Instructions To access the Cisco Router and Security Device Manager(SDM) utility click on the console host icon that is connected to a ISR router. You can click on the grey buttons below to view the different windows. Each of the windows can be minimized by clicking on the [-].You can also reposition a window by dragging it by the title bar. The "Tab" key and most commands that use the "Control"or "Escape" keys are not supported and are not necessary to complete this simulation.




A.1. Which two options correctly identify the associated interface with the correct security zone? (Choose two.)
A: FastEthernet0/1 is associated to the "out-zone" zone.
B: FastEthernet0/0 is associated to the "in-zone" zone.
C: FastEthernet0/0 and 0/1 are associated to the "self" zone.
D: FastEthernet0/0 and 0/1 are associated to the "in-zone" zone.
E: FastEthernet0/0 and 0/1 are associated to the "out-zone" zone.
F: FastEthernet0/0 and 0/1 are not associated to any zone.
Answer: A, B
2 . Which statements is correct regarding the "sdm-permit" policy map?
A: Traffic not matched by any of the class maps within that policy map will be inspected
B: Traffic matching the "sdm-access" traffic class will be inspected.
C: Traffic matching the "SDM_CA_SERVER" traffic class will be dropped.
D: That policy map is applied to traffic sourced from the "self" zone and destined to the "out-zone" zone.
Answer: B

3.
Within the "sdm-inspect" policy map, what is the action assigned to the traffic class "sdm-invalid-src", and which traffic is matched by the traffic class "sdm-invlid-src" ? (Choose two.) A.drop/log B.inspect C.inspect/log D.traffic matched by ACL 104 E.traffic matched by ACL 105 F.traffic matched by the nested "sdm-cls-insp-traffic" class map G.any traffic

Answer: A, D

4.
Which three protocols are matched by the "sdm-cls-insp-traffic" class map? (Choose three)


A: sql-net
B: pop3
C: 12tp
D: ftp
Answer: A, B, D
5. Within the "sdm-permit" policy map, what is the action assigned to the traffic class "class-default"?
A: inspect
B: pass
C: drop
D: police
Answer: C
6. Which ploicy map is associated to the "adm-zp-in-out" security zone pair?
A.sdm-permit-icmpreply B.adm-permit C.sdm-inspect D.sdm-insp-traffic E.sdm-access
Answer: C
QUESTION 146
LAB

You are the passguide network security administrator for Big Money BankCo. You are informed that an
attacker has performed a CAM table overflow attack by sending spoofed MAC addresses on one of the switch ports. The attacker has since been identified and escorted out of the campus. You now need to take action to configure the swtich port to protect against this kind of attack in the future. For purposes of this test, the attacker was connected via a hub to the Fa0/12 interface of the switch. The topology is provided for your use. The enable password of the switch is cisco. Your task is to configure the Fa0/12 interface on the switch to limit the maximum number of MAC addresses that are allowed to access the port to two and to shutdown the interface when there is a violation.





A. Switch1>enable Switch1#config t Switch1(config)#interface fa0/12 Switch1(config-if)#switchport mode access Switch1(config-if)#switchport port-security maximum 2 Switch1(config-if)#switchport port-security violation shutdown Switch1(config-if)#no shut Switch1(config-if)#end Switch1#copy run start
Answer: A
QUESTION 147
Please choose the correct description about Cisco Self-Defending Network characteristics.

A. INTEGRATED -PG1

COLLABORATIVE -PG2 ADAPTIVE -PG3
B. INTEGRATED -PG2 COLLABORATIVE -PG1 ADAPTIVE -PG3
C. INTEGRATED -PG2 COLLABORATIVE -PG3 ADAPTIVE -PG1
D. INTEGRATED -PG3 COLLABORATIVE -PG2 ADAPTIVE -PG1

Answer: B
QUESTION 148
With the increasing development of network, various network attacks appear. Which statement best describes the relationships between the attack method and the result?

A. Ping Sweep -PG1 and PG3 Port Scan -PG2, PG4 and PG5
B. Ping Sweep -PG2 and PG4 Port Scan -PG1, PG3 and PG5
C. Ping Sweep -PG1 and PG5 Port Scan -PG2, PG3 and PG4
D. Ping Sweep -PG2 and PG3 Port Scan -PG1, PG4 and PG5

Answer: B
QUESTION 149
Please choose the correct matching relationships between the cryptography algorithms and the type of algorithm.


A. Symmetric -PG1, PG2 and PG3 Asymmetric -PG4, PG5 and PG6
B. Symmetric -PG1, PG4 and PG5 Asymmetric -PG2, PG3 and PG6
C. Symmetric -PG2, PG4 and PG5 Asymmetric -PG1, PG3 and PG6
D. Symmetric -PG2, PG5 and PG6 Asymmetric -PG1, PG3 and PG4
Answer: B
QUESTION 150
Which are the best practices for attack mitigations?


A. PG1, PG2, PG3 and PG5
B. PG2, PG5, PG6 and PG8
C. PG2, PG5, PG6 and PG7
D. PG2, PG3, PG6 and PG8
E. PG3, PG4, PG6 and PG7

Answer: B
QUESTION 151
Which statement best describes the relationships between AAA function and TACACS+, RADIUS based on the exhibit shown?

A. TACACS+ -PG1 and PG3 RADIUS -PG2 and PG4
B. TACACS+ -PG2 and PG4 RADIUS -PG1 and PG3
C. TACACS+ -PG1 and PG4 RADIUS -PG2 and PG3
D. TACACS+ -PG2 and PG3 RADIUS -PG1 and PG4

Answer: B
QUESTION 152
Which item is the correct matching relationships associated with IKE Phase?


A. IKE Phase 1 -PG1 and PG2 IKE Phase 2 -PG3, PG4 and PG5
B. IKE Phase 1 -PG1 and PG4 IKE Phase 2 -PG2, PG3 and PG5
C. IKE Phase 1 -PG2 and PG3 IKE Phase 2 -PG1, PG4 and PG5
D. IKE Phase 1 -PG2 and PG4 IKE Phase 2 -PG1, PG3 and PG5

Answer: B
QUESTION 153
Which two statements about configuring the Cisco ACS server to perform router command authorization are ture? (Choose two.)

A.In the ACS User Group setyp screen, use Shell Command Authorization Set options to configure which commands and command arguments to permit or deny.
B.From the ACS Interface Configuration screen,select RADIUS (Cisco IOS/PIX 6.0), and then enable the Shell (exec) option on the RADIUS Services screen.
C.When adding the router as an AAA client on the Cisco ACS server,choose the TACACS+ (CISCO IOS) protocol.

D.Configure the Cisco ACS server to forward authentication of users to an external user databases, like Windows Database.

Answer: AC
QUESTION 154
Which statement best describes the relationships between AAA function and TACACS+, RADIUS based on the exhibit shown? Move the statements to either TACACS+ or to RADIUS.

Answer:


QUESTION 155
Drag&Drop

Answer:


QUESTION 156
Drag two characteristics of the SDM Security Audit wizard on the above to the list on the below.


Answer:


QUESTION 157
On the basis of the description of SSL-based VPN, place the correct descriptions in the proper locations.

Answer:




Which of these is used to define which traffic will be protected by IPsec between the Next Gen University Santa

Cruz main campus and its SAC remote campus?
A. ACL 177
B. ACL 167
C. ACL 152
D. ESP-3DES-SHA1 transform set
E. ESP-3DES-SHA2 transform set
F. IKE Phase 1

Answer: A
QUESTION 159
Which three items are Cisco best-practice recommendations for securing a network? (Choose three.)
A. Deploy HIPS software on all end-user workstations.
B. Routinely apply patches to operating systems and applications.
C. Disable unneeded services and ports on hosts.
D. Require strong passwords, and enable password expiration.

Answer: BCD
QUESTION 160
Observe the following options carefully, which two attacks focus on RSA? (Choose all that apply.)
A. DDoS attack
B. BPA attack
C. Adaptive chosen ciphertext attack
D. Man-in-the-middle attack
Answer: BC
QUESTION 161
Which item is the correct matching relationships associated with IKE Phase?


A. IKE Phase 1 -PG1 and PG2 IKE Phase 2 -PG3, PG4 and PG5
B. IKE Phase 1 -PG1 and PG4 IKE Phase 2 -PG2, PG3 and PG5
C. IKE Phase 1 -PG2 and PG3 IKE Phase 2 -PG1, PG4 and PG5
D. IKE Phase 1 -PG2 and PG4 IKE Phase 2 -PG1, PG3 and PG5

Answer: B


Which two options correctly Identify the associated interface with the correct security zone? (Choose two)
A. FastEthernet0/1 is associated to the ��out-zone�� zone.
B. FastEthernet0/0 is associated to the ��in-zone�� zone.
C. FastEthernet0/0 and 0/1 are associated to the ��self�� zone.
D. FastEthernet0/0 and 0/1 are associated to the ��in-zone�� zone.
E. FastEthernet0/0 and 0/1 are associated to the ��out-zone�� zone.
F. FastEthernet0/0 and 0/1 are not associated to any zone.
Answer: AB

Which statement is correct regarding the ��sdm-permit�� policy map?
A. Traffic not matched by any of the class maps within that policy map will be inspected.

B. Traffic matching the ��sdm-access�� traffic class will be inspected.
C. Traffic matching the ��SDM_CA_SERVER�� traffic class will be dropped.
D. That policy map is applied to traffic sourced from the ��self�� zone and destined to the ��out-zone�� zone.
Answer: B

Which three protocols are matched by the ��sdm-cls-insp-traffic�� class map? (Choose three)

A. sql-net
B. pop3
C. 12tp
D. ftp
Answer: ABD

Within the ��sdm-permit�� policy map, what is the action assigned to the traffic class ��class-default��?
A. inspect
B. pass
C. drop
D. police

Answer: C QUESTION 166 Zone-based Firewall SDM Simlet




Which policy map is associated to the ��sdm-zp-in-out�� security zone pair?
A. sdm-permit-icmpreply
B. sdm-permit
C. sdm-inspect
D. sdm-insp-traffic

Answer: C
QUESTION 167 Zone-based Firewall SDM Simlet


Within the ��sdm-inspect�� policy map, what is the action assigned to the traffic class ��sdm-invalid-src��, and which traffic is matched by the traffic class ��sdm-invalid-src�� ? (Choose two)
A. traffic matched by ACL 105
B. traffic matched by the nested ��sdm-cls-insp-traffic�� class map
C. drop/log
D. traffic matched by ACL 104
Answer: AC
QUESTION 168
Drag two characteristics of the SDM Security Audit wizard on the above to the list on the below.


Answer:


QUESTION 169
On the basis of the description of SSL-based VPN, place the correct descriptions in the proper locations.


Answer:


QUESTION 170 Site-to-site VPN SDM Lab Sim



The Ipsec tunnel to the SAC remote campus terminates at which IP address, and what is the protected subnet behind the SAC remote campus router? (Choose two)
A. 192.168.2.57
B. 192.168.5.48
C. 192.168.8.58
D. 10.2.54.0/24
E. 10.5.66.0/24
F. 10.8.75.0/24

Answer: CF
QUESTION 171 Site-to-site VPN SDM Lab Sim



Which one of these statements is correct in regards to Next Gen University Ipsec tunnel between its Santa Cruz main campus and its SJ remote campus?
A.It is using Ipsec tunnel mode, AES encryption, and SHA HMAC integrity Check. B.It is using Ipsec transport mode, 3DES encryption, and SHA HMAC integrity Check. C.It is using Ipsec tunnel mode to protect the traffic between the 10.10.10.0/24 and the 10.2.54.0/24 subnet. D.It is using digital certificate to authenticate between the Ipsec peers and DH group 2. E.It is using pre-shared key to authenticate between the Ipsec peers and DH group 5.
Answer: C
QUESTION 172

Site-to-site VPN SDM Lab Sim

Which one of these statements is correct in regards to Next Gen University Ipsec tunnel between its Santa Cruz main campus and its SAC remote campus?
A.The SAC remote campus remote router is using dynamic IP address; therefore, the Santa Cruz router is using a dynamic crypto map.
B.Dead Peer Detection (DPD) is used to monitor the Ipsec tunnel, so if there is no traffic traversing between the two sites, the Ipsec tunnel will disconnect.
C.Tunnel mode is used; therefore, a GRE tunnel interface will be configured.
D.Only the ESP protocol is being used; AH is not being used.
Answer: D